Bootlogs

OpenWrt

U-Boot SPL 2018.03-00006-g3f3fcc06e9-dirty (Mar 23 2018 - 16:46:25 +1100)
Initializing DDR....
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
Trying to boot from NAND


U-Boot 2018.03-00006-g3f3fcc06e9-dirty (Mar 23 2018 - 16:46:25 +1100)

SoC:  LS1043AE Rev1.1 (0x87920011)
Clock Configuration:
       CPU0(A53):1600 MHz  CPU1(A53):1600 MHz  CPU2(A53):1600 MHz  
       CPU3(A53):1600 MHz  
       Bus:      400  MHz  DDR:      1600 MT/s  FMAN:     500  MHz
Reset Configuration Word (RCW):
       00000000: 08100010 0a000000 00000000 00000000
       00000010: 14550002 80004012 e0025000 c1002000
       00000020: 00000000 00000000 00000000 00228ffc
       00000030: 00000000 00201101 00000096 00000001
Model: Traverse LS1043S
Board: LS1043S, booting from NAND
I2C:   ready
DRAM:  Detected UDIMM Fixed DDR on board
3.9 GiB (DDR4, 32-bit, CL=11, ECC off)
Using SERDES1 Protocol: 5205 (0x1455)
SEC0: RNG instantiated
PPA Firmware: Version LSDK-17.09-update-103017
NAND:  512 MiB
MMC:   FSL_SDHC: 0
Loading Environment from NAND... OK
uC:    OK
In:    serial
Out:   serial
Err:   serial
Net:   Retimer: DS125DF111 found
OK
Fman1: Uploading microcode version 108.4.5
AR8031: Enable TXCLK Delay
PCIe0: pcie@3400000 disabled
PCIe1: pcie@3500000 Root Complex: x1 gen1
PCIe2: pcie@3600000 Root Complex: no link
FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3 [PRIME], FM1@DTSEC4, FM1@DTSEC5, FM1@DTSEC6, FM1@TGEC1
Hit any key to stop autoboot: 10  9  8  7  6  5  4  3  2  1  0 

NAND read: device 0 offset 0x1c0000, size 0x20000
 131072 bytes read: OK
MMC: no card present
starting USB...
USB0:   Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
USB1:   Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
USB2:   Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: device type unknown
... is now current device
** Bad device usb 0 **
** Bad device usb 0 **
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=5", size 400 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 3200, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 0
ubi0: available PEBs: 866, total reserved PEBs: 2334, PEBs reserved for bad PEB handling: 80
Read 0 bytes from volume kernel2 to a0000000
No size specified -> Using max size (8507392)
## Loading kernel from FIT Image at a0000000 ...
   Using 'ls1043s' configuration
   Trying 'kernel@0' kernel subimage
     Description:  Linux Kernel
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0xa00000d4
     Data Size:    6866978 Bytes = 6.5 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x80080000
     Entry Point:  0x80080000
     Hash algo:    sha1
     Hash value:   2ee4b9a2a35722063844507b956eac180e879cc5
   Verifying Hash Integrity ... sha1+ OK
## Loading fdt from FIT Image at a0000000 ...
   Using 'ls1043s' configuration
   Trying 'fdt@0' fdt subimage
     Description:  Flattened Device Tree blob Traverse_LS1043S
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0xa068ca00
     Data Size:    29233 Bytes = 28.5 KiB
     Architecture: AArch64
     Load Address: 0x90000000
     Hash algo:    sha1
     Hash value:   cb5e2007f635dd6e0cf747ed18353fb84a6f7deb
   Verifying Hash Integrity ... sha1+ OK
   Loading fdt from 0xa068ca00 to 0x90000000
   Booting using the fdt blob at 0x90000000
   Uncompressing Kernel Image ... OK
   Using Device Tree in place at 0000000090000000, end 000000009001a230

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.91 (matt@development) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6550+42-83e1fce17a) ) #0 SMP PREEMPT Tue Apr 3 23:43:10 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] earlycon: uart8250 at MMIO 0x00000000021c0500 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] OF: reserved mem: initialized node qman-fqd, compatible id fsl,qman-fqd
[    0.000000] OF: reserved mem: initialized node qman-pfdr, compatible id fsl,qman-pfdr
[    0.000000] OF: reserved mem: initialized node bman-fbpr, compatible id fsl,bman-fbpr
[    0.000000] cma: Reserved 16 MiB at 0x00000000fac00000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000008ffbfffff]
[    0.000000] NUMA: Adding memblock [0x80000000 - 0xfbdfffff] on node 0
[    0.000000] NUMA: Adding memblock [0x880000000 - 0x8fbffffff] on node 0
[    0.000000] NUMA: Adding memblock [0x8ff000000 - 0x8ffbfffff] on node 0
[    0.000000] NUMA: Initmem setup node 0 [mem 0x80000000-0x8ffbfffff]
[    0.000000] NUMA: NODE_DATA [mem 0x8ffbc9900-0x8ffbcb0bf]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000080000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000008ffbfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x00000000fbdfffff]
[    0.000000]   node   0: [mem 0x0000000880000000-0x00000008fbffffff]
[    0.000000]   node   0: [mem 0x00000008ff000000-0x00000008ffbfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000008ffbfffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.2 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] percpu: Embedded 22 pages/cpu @ffff80087fb6e000 s52952 r8192 d28968 u90112
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1002192
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: console=ttyS0,115200 earlycon=uart8250,mmio,0x21c0500 root=ubi0:rootfs2 rootfstype=ubifs rootwait mtdparts=7e800000.flash:1m(nand_uboot),384k(nand_uboot_env),128k(fman_fw),256k(ppa),128k(dtb),400m(nandubi) ubi.mtd=nandubi
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] software IO TLB [mem 0xf6c00000-0xfac00000] (64MB) mapped at [ffff800076c00000-ffff80007abfffff]
[    0.000000] Memory: 3909104K/4073472K available (10428K kernel code, 598K rwdata, 3176K rodata, 640K init, 925K bss, 147984K reserved, 16384K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
[    0.000000]       .text : 0xffff000008080000 - 0xffff000008ab0000   ( 10432 KB)
[    0.000000]     .rodata : 0xffff000008ab0000 - 0xffff000008dd0000   (  3200 KB)
[    0.000000]       .init : 0xffff000008dd0000 - 0xffff000008e70000   (   640 KB)
[    0.000000]       .data : 0xffff000008e70000 - 0xffff000008f05a00   (   599 KB)
[    0.000000]        .bss : 0xffff000008f05a00 - 0xffff000008fecf14   (   926 KB)
[    0.000000]     fixed   : 0xffff7dfffe7fd000 - 0xffff7dfffec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
[    0.000000]               0xffff7e0000000000 - 0xffff7e0021ff0000   (   543 MB actual)
[    0.000000]     memory  : 0xffff800000000000 - 0xffff80087fc00000   ( 34812 MB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Adjusting CPU interface base to 0x000000000142f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arm_arch_timer: Enabling workaround for FSL erratum A-008585
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.008429] Console: colour dummy device 80x25
[    0.012924] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
[    0.023329] pid_max: default: 32768 minimum: 301
[    0.028038] Security Framework initialized
[    0.032743] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.041942] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.049865] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.056610] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.064348] ASID allocator initialised with 65536 entries
[    0.101969] EFI services will not be available.
[    0.146638] Detected VIPT I-cache on CPU1
[    0.146663] CPU1: Booted secondary processor [410fd034]
[    0.178662] Detected VIPT I-cache on CPU2
[    0.178677] CPU2: Booted secondary processor [410fd034]
[    0.210707] Detected VIPT I-cache on CPU3
[    0.210722] CPU3: Booted secondary processor [410fd034]
[    0.210755] Brought up 4 CPUs
[    0.241535] SMP: Total of 4 processors activated.
[    0.246260] CPU features: detected feature: 32-bit EL0 Support
[    0.252142] CPU: All CPU(s) started at EL2
[    0.256263] alternatives: patching kernel code
[    0.265186] DMI not present or invalid.
[    0.269161] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.278974] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.285582] xor: measuring software checksum speed
[    0.330421]    8regs     :  3070.000 MB/sec
[    0.374646]    8regs_prefetch:  2737.000 MB/sec
[    0.419220]    32regs    :  3774.000 MB/sec
[    0.463444]    32regs_prefetch:  3175.000 MB/sec
[    0.468080] xor: using function: 32regs (3774.000 MB/sec)
[    0.474146] NET: Registered protocol family 16
[    0.498630] cpuidle: using governor menu
[    0.502970] Bman ver:0a02,02,01
[    0.507540] qman-fqd addr 0x00000008ffc00000 size 0x400000
[    0.513053] qman-pfdr addr 0x00000008fc000000 size 0x2000000
[    0.518742] Qman ver:0a01,03,02,00
[    0.522269] vdso: 2 pages (1 code @ ffff000008ab6000, 1 data @ ffff000008e75000)
[    0.530087] DMA: preallocated 256 KiB pool for atomic allocations
[    0.536287] Serial: AMBA PL011 UART driver
[    0.541238] Machine: Traverse LS1043S
[    0.544917] SoC family: QorIQ LS1043A
[    0.548588] SoC ID: svr:0x87920011, Revision: 1.1
[    0.585583] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.657441] raid6: int64x1  gen()   509 MB/s
[    0.729505] raid6: int64x1  xor()   491 MB/s
[    0.801547] raid6: int64x2  gen()   830 MB/s
[    0.873529] raid6: int64x2  xor()   716 MB/s
[    0.945588] raid6: int64x4  gen()  1245 MB/s
[    1.017611] raid6: int64x4  xor()   879 MB/s
[    1.089658] raid6: int64x8  gen()  1497 MB/s
[    1.161711] raid6: int64x8  xor()   899 MB/s
[    1.233726] raid6: neonx1   gen()   950 MB/s
[    1.305773] raid6: neonx1   xor()   865 MB/s
[    1.377813] raid6: neonx2   gen()  1582 MB/s
[    1.449836] raid6: neonx2   xor()  1338 MB/s
[    1.521885] raid6: neonx4   gen()  2099 MB/s
[    1.593908] raid6: neonx4   xor()  1560 MB/s
[    1.665949] raid6: neonx8   gen()  2151 MB/s
[    1.737985] raid6: neonx8   xor()  1560 MB/s
[    1.742272] raid6: using algorithm neonx8 gen() 2151 MB/s
[    1.747693] raid6: .... xor() 1560 MB/s, rmw enabled
[    1.752678] raid6: using intx1 recovery algorithm
[    1.757486] ACPI: Interpreter disabled.
[    1.763211] RCPM: layerscape_rcpm_init: Can't find the RCPM node.
[    1.769892] vgaarb: loaded
[    1.772777] SCSI subsystem initialized
[    1.777009] imx-i2c 2180000.i2c: fsl-scl-gpio not found
[    1.782298] imx-i2c 2180000.i2c: can't get pinctrl, bus recovery not supported
[    1.789758] 0-0024 supply vcc not found, using dummy regulator
[    1.808301] i2c i2c-0: IMX I2C adapter registered
[    1.813060] i2c i2c-0: using dma0chan16 (tx) and dma0chan17 (rx) for DMA transfers
[    1.820732] imx-i2c 21b0000.i2c: fsl-scl-gpio not found
[    1.826010] imx-i2c 21b0000.i2c: can't get pinctrl, bus recovery not supported
[    1.833384] i2c i2c-1: IMX I2C adapter registered
[    1.838116] i2c i2c-1: can't use DMA, using PIO instead.
[    1.843579] pps_core: LinuxPPS API ver. 1 registered
[    1.848568] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.857758] PTP clock support registered
[    1.861792] dmi: Firmware registration failed.
[    1.866277] bman-fbpr addr 0x00000008fe000000 size 0x1000000
[    1.871986] Bman err interrupt handler present
[    1.876858] Bman portal initialised, cpu 0
[    1.881042] Bman portal initialised, cpu 1
[    1.885223] Bman portal initialised, cpu 2
[    1.889407] Bman portal initialised, cpu 3
[    1.893520] Bman portals initialised
[    1.897989] Qman err interrupt handler present
[    1.902648] QMan: Allocated lookup table at ffff000009c01000, entry count 65537
[    1.910346] Qman portal initialised, cpu 0
[    1.914524] Qman portal initialised, cpu 1
[    1.918700] Qman portal initialised, cpu 2
[    1.922876] Qman portal initialised, cpu 3
[    1.926991] Qman portals initialised
[    1.930640] Bman: BPID allocator includes range 32:32
[    1.935764] Qman: FQID allocator includes range 256:256
[    1.941015] Qman: FQID allocator includes range 32768:32768
[    1.946660] Qman: CGRID allocator includes range 0:256
[    1.951958] Qman: pool channel allocator includes range 1025:15
[    1.957993] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree
[    1.964056] fsl-ifc 1530000.ifc: Freescale Integrated Flash Controller
[    1.970623] fsl-ifc 1530000.ifc: IFC version 1.4, 8 banks
[    1.976258] Advanced Linux Sound Architecture Driver Initialized.
[    1.982862] clocksource: Switched to clocksource arch_sys_counter
[    1.989079] VFS: Disk quotas dquot_6.6.0
[    1.993052] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    2.000086] pnp: PnP ACPI: disabled
[    2.006791] NET: Registered protocol family 2
[    2.011523] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    2.019004] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    2.026056] TCP: Hash tables configured (established 32768 bind 32768)
[    2.032671] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    2.038770] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    2.045381] NET: Registered protocol family 1
[    2.050050] kvm [1]: 8-bit VMID
[    2.053205] kvm [1]: IDMAP page: 80a9c000
[    2.057234] kvm [1]: HYP VA range: 800000000000:ffffffffffff
[    2.063357] kvm [1]: Hyp mode initialized successfully
[    2.068549] kvm [1]: vgic-v2@1440000
[    2.072203] kvm [1]: vgic interrupt IRQ1
[    2.076152] kvm [1]: virtual timer IRQ4
[    2.081212] audit: initializing netlink subsys (disabled)
[    2.086667] audit: type=2000 audit(2.008:1): initialized
[    2.092024] No memory allocated for crashlog
[    2.096417] workingset: timestamp_bits=44 max_order=20 bucket_order=0
[    2.103228] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.109107] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.119058] fuse init (API version 7.26)
[    2.123060] SGI XFS with security attributes, realtime, no debug enabled
[    2.131556] async_tx: api initialized (async)
[    2.135969] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    2.143450] io scheduler noop registered
[    2.147401] io scheduler cfq registered (default)
[    2.153559] OF: PCI: host bridge /soc/pcie@3500000 ranges:
[    2.159083] OF: PCI:    IO 0x4800010000..0x480001ffff -> 0x00000000
[    2.165388] OF: PCI:   MEM 0x4840000000..0x487fffffff -> 0x40000000
[    2.171806] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0000:00
[    2.178548] pci_bus 0000:00: root bus resource [bus 00-ff]
[    2.184061] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    2.190276] pci_bus 0000:00: root bus resource [mem 0x4840000000-0x487fffffff] (bus address [0x40000000-0x7fffffff])
[    2.210914] pci 0000:00:00.0: BAR 14: assigned [mem 0x4840000000-0x48402fffff]
[    2.218179] pci 0000:00:00.0: BAR 6: assigned [mem 0x4840300000-0x48403007ff pref]
[    2.225793] pci 0000:01:00.0: BAR 0: assigned [mem 0x4840000000-0x48401fffff 64bit]
[    2.233529] pci 0000:01:00.0: BAR 6: assigned [mem 0x4840200000-0x484020ffff pref]
[    2.241139] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    2.246393] pci 0000:00:00.0:   bridge window [mem 0x4840000000-0x48402fffff]
[    2.253707] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[    2.260708] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    2.267401] OF: PCI: host bridge /soc/pcie@3600000 ranges:
[    2.272922] OF: PCI:    IO 0x5000010000..0x500001ffff -> 0x00000000
[    2.279223] OF: PCI:   MEM 0x5040000000..0x507fffffff -> 0x40000000
[    2.285618] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0001:00
[    2.292355] pci_bus 0001:00: root bus resource [bus 00-ff]
[    2.297871] pci_bus 0001:00: root bus resource [io  0x10000-0x1ffff] (bus address [0x0000-0xffff])
[    2.306879] pci_bus 0001:00: root bus resource [mem 0x5040000000-0x507fffffff] (bus address [0x40000000-0x7fffffff])
[    2.317682] pci 0001:00:00.0: BAR 6: assigned [mem 0x5040000000-0x50400007ff pref]
[    2.325293] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    2.330662] pcieport 0001:00:00.0: Signaling PME through PCIe PME interrupt
[    2.339326] Freescale LS2 console driver
[    2.343313] fsl-ls2-console: device fsl_mc_console registered
[    2.349124] fsl-ls2-console: device fsl_aiop_console registered
[    2.355542] xenfs: not registering filesystem on non-xen platform
[    2.363298] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.370547] console [ttyS0] disabled
[    2.374165] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 36, base_baud = 25000000) is a 16550A
[    2.383018] console [ttyS0] enabled
[    2.383018] console [ttyS0] enabled
[    2.390000] bootconsole [uart8250] disabled
[    2.390000] bootconsole [uart8250] disabled
[    2.398556] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 36, base_baud = 25000000) is a 16550A
[    2.407514] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 37, base_baud = 25000000) is a 16550A
[    2.416470] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 37, base_baud = 25000000) is a 16550A
[    2.431393] brd: module loaded
[    2.437204] loop: module loaded
[    2.440666] hisi_sas: driver version v1.6
[    2.447341] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xac
[    2.453694] nand: Winbond NAND 512MiB 1,8V 8-bit
[    2.458316] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    2.466165] Bad block table found at page 262080, version 0x01
[    2.472563] Bad block table found at page 262016, version 0x01
[    2.478683] 6 cmdlinepart partitions found on MTD device 7e800000.flash
[    2.485298] Creating 6 MTD partitions on "7e800000.flash":
[    2.490782] 0x000000000000-0x000000100000 : "nand_uboot"
[    2.496597] 0x000000100000-0x000000160000 : "nand_uboot_env"
[    2.502709] 0x000000160000-0x000000180000 : "fman_fw"
[    2.508206] 0x000000180000-0x0000001c0000 : "ppa"
[    2.513360] 0x0000001c0000-0x0000001e0000 : "dtb"
[    2.518504] 0x0000001e0000-0x0000191e0000 : "nandubi"
[    2.524717] fsl,ifc-nand 7e800000.nand: IFC NAND device at 0x7e800000, bank 0
[    2.532753] libphy: Fixed MDIO Bus: probed
[    2.537320] tun: Universal TUN/TAP device driver, 1.6
[    2.542366] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.549218] libphy: Freescale XGMAC MDIO Bus: probed
[    2.555512] libphy: Freescale XGMAC MDIO Bus: probed
[    2.560540] libphy: Freescale XGMAC MDIO Bus: probed
[    2.565697] libphy: Freescale XGMAC MDIO Bus: probed
[    2.570852] libphy: Freescale XGMAC MDIO Bus: probed
[    2.576007] libphy: Freescale XGMAC MDIO Bus: probed
[    2.581162] libphy: Freescale XGMAC MDIO Bus: probed
[    2.586317] libphy: Freescale XGMAC MDIO Bus: probed
[    2.591473] libphy: Freescale XGMAC MDIO Bus: probed
[    2.608433] Freescale FM module, FMD API version 21.1.0
[    2.615948] Freescale FM Ports module
[    2.619606] fsl_mac: fsl_mac: FSL FMan MAC API based driver
[    2.625615] fsl_mac 1ae0000.ethernet: FMan MEMAC
[    2.630233] fsl_mac 1ae0000.ethernet: FMan MAC address: 00:0a:fa:24:23:79
[    2.637343] fsl_mac 1ae2000.ethernet: FMan MEMAC
[    2.641960] fsl_mac 1ae2000.ethernet: FMan MAC address: 00:0a:fa:24:23:7a
[    2.648960] Setting up fixed link, speed 1000 duplex 1
[    2.654106] fsl_mac 1ae4000.ethernet: FMan MEMAC
[    2.658721] fsl_mac 1ae4000.ethernet: FMan MAC address: 00:0a:fa:24:23:7d
[    2.665688] Setting up fixed link, speed 1000 duplex 1
[    2.670835] fsl_mac 1ae6000.ethernet: FMan MEMAC
[    2.675451] fsl_mac 1ae6000.ethernet: FMan MAC address: 00:0a:fa:24:23:7e
[    2.682564] fsl_mac 1ae8000.ethernet: FMan MEMAC
[    2.687180] fsl_mac 1ae8000.ethernet: FMan MAC address: 00:0a:fa:24:23:7b
[    2.694291] fsl_mac 1aea000.ethernet: FMan MEMAC
[    2.698909] fsl_mac 1aea000.ethernet: FMan MAC address: 00:0a:fa:24:23:7c
[    2.705883] Setting up fixed link, speed 1000 duplex 1
[    2.711028] fsl_mac 1af0000.ethernet: FMan MEMAC
[    2.715645] fsl_mac 1af0000.ethernet: FMan MAC address: 00:0a:fa:24:23:7f
[    2.722456] fsl_dpa: FSL DPAA Ethernet driver
[    2.727771] fsl_dpa soc:fsl,dpaa:ethernet@0: Skip RX PCD High Priority FQs initialization
[    2.739744] fsl_dpa: fsl_dpa: Probed interface eth0
[    2.745265] fsl_dpa soc:fsl,dpaa:ethernet@1: Skip RX PCD High Priority FQs initialization
[    2.757482] fsl_dpa: fsl_dpa: Probed interface eth1
[    2.763153] fsl_dpa soc:fsl,dpaa:ethernet@2: Skip RX PCD High Priority FQs initialization
[    2.775613] fsl_dpa: fsl_dpa: Probed interface eth2
[    2.781395] fsl_dpa soc:fsl,dpaa:ethernet@3: Skip RX PCD High Priority FQs initialization
[    2.794113] fsl_dpa: fsl_dpa: Probed interface eth3
[    2.800041] fsl_dpa soc:fsl,dpaa:ethernet@4: Skip RX PCD High Priority FQs initialization
[    2.813006] fsl_dpa: fsl_dpa: Probed interface eth4
[    2.819050] fsl_dpa soc:fsl,dpaa:ethernet@5: Skip RX PCD High Priority FQs initialization
[    2.832351] fsl_dpa: fsl_dpa: Probed interface eth5
[    2.838528] fsl_dpa soc:fsl,dpaa:ethernet@8: Skip RX PCD High Priority FQs initialization
[    2.852029] fsl_dpa: fsl_dpa: Probed interface eth6
[    2.856954] fsl_advanced: FSL DPAA Advanced drivers:
[    2.861913] fsl_proxy: FSL DPAA Proxy initialization driver
[    2.867714] fsl_oh: FSL FMan Offline Parsing port driver
[    2.873474] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[    2.880516] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    2.886307] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    2.892186] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    2.898139] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    2.905094] igb: Copyright (c) 2007-2014 Intel Corporation.
[    2.910691] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    2.918513] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    2.924450] sky2: driver version 1.30
[    2.928661] VFIO - User Level meta-driver version: 0.3
[    2.934084] mousedev: PS/2 mouse device common for all mice
[    2.940067] i2c /dev entries driver
[    2.944500] i2c i2c-1: Added multiplexed i2c bus 2
[    2.949399] i2c i2c-1: Added multiplexed i2c bus 3
[    2.954189] pca954x 1-0070: registered 2 multiplexed busses for I2C mux pca9540
[    2.962405] imx2-wdt 2ad0000.wdog: timeout 60 sec (nowayout=0)
[    2.968602] qoriq_cpufreq: Freescale QorIQ CPU frequency scaling driver
[    2.975604] sdhci: Secure Digital Host Controller Interface driver
[    2.981780] sdhci: Copyright(c) Pierre Ossman
[    2.986200] Synopsys Designware Multimedia Card Interface Driver
[    2.992633] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.034876] mmc0: SDHCI controller on 1560000.esdhc [1560000.esdhc] using ADMA 64-bit
[    3.044627] ledtrig-cpu: registered to indicate activity on CPUs
[    3.051640] platform caam_qi: Linux CAAM Queue I/F driver initialised
[    3.058083] caam 1700000.crypto: device ID = 0x0a12060000000000 (Era 8)
[    3.064695] caam 1700000.crypto: job rings = 3, qi = 1, dpaa2 = no
[    3.073750] caam algorithms registered in /proc/crypto
[    3.080571] platform caam_qi: algorithms registered in /proc/crypto
[    3.087771] caam_jr 1710000.jr: registering rng-caam
[    3.092787] caam 1700000.crypto: caam pkc algorithms registered in /proc/crypto
[    3.101349] Freescale USDPAA process driver
[    3.105531] fsl-usdpaa: no region found
[    3.109361] Freescale USDPAA process IRQ driver
[    3.114766] Initializing XFRM netlink socket
[    3.119088] NET: Registered protocol family 10
[    3.124203] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.130442] NET: Registered protocol family 17
[    3.134897] 8021q: 802.1Q VLAN Support v1.8
[    3.139092] Key type dns_resolver registered
[    3.143364] Key type ceph registered
[    3.146988] libceph: loaded (mon/osd proto 15/24)
[    3.151994] registered taskstats version 1
[    3.156630] Btrfs loaded, crc32c=crc32c-generic
[    3.161815] ubi0: attaching mtd5
[    3.226224] random: fast init done
[    4.847560] ubi0: scanning is finished
[    4.858822] ubi0: attached mtd5 (name "nandubi", size 400 MiB)
[    4.864652] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.871523] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.878303] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.885260] ubi0: good PEBs: 3200, bad PEBs: 0, corrupted PEBs: 0
[    4.891347] ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
[    4.898565] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 0
[    4.906943] ubi0: available PEBs: 866, total reserved PEBs: 2334, PEBs reserved for bad PEB handling: 80
[    4.916427] ubi0: background thread "ubi_bgt0d" started, PID 2217
[    4.916690] hctosys: unable to open rtc device (rtc0)
[    4.916841] ALSA device list:
[    4.916842]   No soundcards found.
[    4.989209] UBIFS (ubi0:3): UBIFS: mounted UBI device 0, volume 3, name "rootfs2", R/O mode
[    4.997557] UBIFS (ubi0:3): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    5.007468] UBIFS (ubi0:3): FS size: 132943872 bytes (126 MiB, 1047 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    5.018155] UBIFS (ubi0:3): reserved for root: 0 bytes (0 KiB)
[    5.023983] UBIFS (ubi0:3): media format: w4/r0 (latest is w4/r0), UUID 0A8E6318-2AB3-4327-8BE9-8FDD2F5BDC3F, small LPT model
[    5.036766] VFS: Mounted root (ubifs filesystem) readonly on device 0:12.
[    5.043730] Freeing unused kernel memory: 640K
[    5.131572] init: Console is alive
[    5.135046] init: - watchdog -
[    5.294875] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.330784] usb_common: no symbol version for module_layout
[    5.358137] usbcore: registered new interface driver usbfs
[    5.363656] usbcore: registered new interface driver hub
[    5.369022] usbcore: registered new device driver usb
[    5.377395] dwc3 2f00000.usb3: request value same as default, ignoring
[    5.384205] dwc3 3000000.usb3: request value same as default, ignoring
[    5.390937] dwc3 3100000.usb3: request value same as default, ignoring
[    5.412090] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.417607] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    5.425488] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x02010010
[    5.434219] xhci-hcd xhci-hcd.0.auto: irq 45, io mem 0x02f00000
[    5.440423] hub 1-0:1.0: USB hub found
[    5.444190] hub 1-0:1.0: 1 port detected
[    5.448264] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.453752] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    5.461432] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.469747] hub 2-0:1.0: USB hub found
[    5.473502] hub 2-0:1.0: 1 port detected
[    5.477595] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    5.483083] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    5.490921] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x02010010
[    5.499633] xhci-hcd xhci-hcd.1.auto: irq 46, io mem 0x03000000
[    5.505780] hub 3-0:1.0: USB hub found
[    5.509535] hub 3-0:1.0: 1 port detected
[    5.513591] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    5.519077] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    5.526751] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.535070] hub 4-0:1.0: USB hub found
[    5.538818] hub 4-0:1.0: 1 port detected
[    5.542916] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[    5.548405] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 5
[    5.556284] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x02010010
[    5.564994] xhci-hcd xhci-hcd.2.auto: irq 47, io mem 0x03100000
[    5.571141] hub 5-0:1.0: USB hub found
[    5.574896] hub 5-0:1.0: 1 port detected
[    5.578987] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[    5.584471] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 6
[    5.592147] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.600459] hub 6-0:1.0: USB hub found
[    5.604214] hub 6-0:1.0: 1 port detected
[    5.614463] usbcore: registered new interface driver usb-storage
[    5.621106] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[    5.629233] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.644391] init: - preinit -
[    5.725610] fsl_dpa soc:fsl,dpaa:ethernet@2 fm1-mac3: renamed from eth2
[    5.755987] fsl_dpa soc:fsl,dpaa:ethernet@4 eth2: renamed from eth4
[    5.779790] fsl_dpa soc:fsl,dpaa:ethernet@3 fm1-mac4: renamed from eth3
[    5.807764] fsl_dpa soc:fsl,dpaa:ethernet@5 eth3: renamed from eth5
[    5.835775] fsl_dpa soc:fsl,dpaa:ethernet@2 eth4: renamed from fm1-mac3
[    5.859754] fsl_dpa soc:fsl,dpaa:ethernet@3 eth5: renamed from fm1-mac4
[    5.866920] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[    6.075710] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.121562] mount_root: mounting /dev/root
[    9.126011] UBIFS (ubi0:3): start fixing up free space
[    9.696229] UBIFS (ubi0:3): free space fixup complete
[    9.706583] UBIFS (ubi0:3): background thread "ubifs_bgt0_3" started, PID 2335
[    9.707782] urandom-seed: Seed file not found (/etc/urandom.seed)
[    9.740703] procd: - early -
[    9.744215] procd: - watchdog -
Failed to connect to ubus
[   10.314993] procd: - watchdog -
[   10.318264] procd: - ubus -
[   10.372293] procd: - init -
Please press Enter to activate this console.
[   10.496036] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.515114] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[   10.535386] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.553946] usbcore: registered new interface driver cdc_acm
[   10.559658] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   10.568672] usbcore: registered new interface driver cdc_wdm
[   10.578066] hso: drivers/net/usb/hso.c: Option Wireless
[   10.583445] usbcore: registered new interface driver hso
[   10.591100] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.605310] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   10.632017] rtc-isl1208 0-006f: rtc core: registered rtc-isl1208 as rtc0
[   10.646205] usbcore: registered new interface driver usbserial
[   10.652099] usbcore: registered new interface driver usbserial_generic
[   10.658716] usbserial: USB Serial support registered for generic
[   10.667319] xt_time: kernel timezone is -0000
[   10.672809] usbcore: registered new interface driver cdc_ether
[   10.681294] usbcore: registered new interface driver cdc_ncm
[   10.687537] usbcore: registered new interface driver huawei_cdc_ncm
[   10.699761] PPP generic driver version 2.4.2
[   10.704867] NET: Registered protocol family 24
[   10.710855] usbcore: registered new interface driver qmi_wwan
[   10.717494] usbcore: registered new interface driver rndis_host
[   10.725137] usbcore: registered new interface driver sierra
[   10.730785] usbserial: USB Serial support registered for Sierra USB modem
[   10.738909] usbcore: registered new interface driver sierra_net
[   10.746975] usbcore: registered new interface driver cdc_mbim
[   10.754474] usbcore: registered new interface driver option
[   10.760198] usbserial: USB Serial support registered for GSM modem (1-port)
[   10.770312] usbcore: registered new interface driver qcserial
[   10.776132] usbserial: USB Serial support registered for Qualcomm USB modem
[   10.783233] kmodloader: done loading kernel modules from /etc/modules.d/*
[   12.110952] random: crng init done
[   13.312042] br-lan: port 1(eth0) entered blocking state
[   13.317366] br-lan: port 1(eth0) entered disabled state
[   13.322789] device eth0 entered promiscuous mode
[   13.327909] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   13.413538] br-lan: port 2(eth1) entered blocking state
[   13.418903] br-lan: port 2(eth1) entered disabled state
[   13.424374] device eth1 entered promiscuous mode
[   13.429134] br-lan: port 2(eth1) entered blocking state
[   13.434379] br-lan: port 2(eth1) entered forwarding state
[   13.440047] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   13.524383] br-lan: port 3(eth2) entered blocking state
[   13.530149] br-lan: port 3(eth2) entered disabled state
[   13.536493] device eth2 entered promiscuous mode
[   13.541737] br-lan: port 3(eth2) entered blocking state
[   13.546981] br-lan: port 3(eth2) entered forwarding state
[   13.632220] br-lan: port 4(eth3) entered blocking state
[   13.637477] br-lan: port 4(eth3) entered disabled state
[   13.643011] device eth3 entered promiscuous mode
[   13.647710] br-lan: port 4(eth3) entered blocking state
[   13.652947] br-lan: port 4(eth3) entered forwarding state
[   13.659943] This is a fixed-link, forcing speed 1000 duplex 1
[   13.670135] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready
[   14.246967] br-lan: port 2(eth1) entered disabled state
[   14.252394] br-lan: port 3(eth2) entered disabled state
[   14.257793] br-lan: port 4(eth3) entered disabled state
[   14.694964] IPv6: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready



BusyBox v1.28.2 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r6600+48-7e42cbaf2a
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# 

Fedora 28 (Traverse Kernel)

U-Boot SPL 2018.03-00006-g3f3fcc06e9-dirty (Mar 23 2018 - 16:46:25 +1100)
Initializing DDR....
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
Trying to boot from NAND


U-Boot 2018.03-00006-g3f3fcc06e9-dirty (Mar 23 2018 - 16:46:25 +1100)

SoC:  LS1043AE Rev1.1 (0x87920011)
Clock Configuration:
       CPU0(A53):1600 MHz  CPU1(A53):1600 MHz  CPU2(A53):1600 MHz  
       CPU3(A53):1600 MHz  
       Bus:      400  MHz  DDR:      1600 MT/s  FMAN:     500  MHz
Reset Configuration Word (RCW):
       00000000: 08100010 0a000000 00000000 00000000
       00000010: 14550002 80004012 e0025000 c1002000
       00000020: 00000000 00000000 00000000 00228ffc
       00000030: 00000000 00201101 00000096 00000001
Model: Traverse LS1043S
Board: LS1043S, booting from NAND
I2C:   ready
DRAM:  Detected UDIMM Fixed DDR on board
3.9 GiB (DDR4, 32-bit, CL=11, ECC off)
Using SERDES1 Protocol: 5205 (0x1455)
SEC0: RNG instantiated
PPA Firmware: Version LSDK-17.09-update-103017
NAND:  512 MiB
MMC:   FSL_SDHC: 0
Loading Environment from NAND... OK
uC:    OK
In:    serial
Out:   serial
Err:   serial
Net:   Retimer: DS125DF111 found
OK
Fman1: Uploading microcode version 108.4.5
AR8031: Enable TXCLK Delay
PCIe0: pcie@3400000 disabled
PCIe1: pcie@3500000 Root Complex: x1 gen1
PCIe2: pcie@3600000 Root Complex: no link
FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3 [PRIME], FM1@DTSEC4, FM1@DTSEC5, FM1@DTSEC6, FM1@TGEC1
Hit any key to stop autoboot: 10  9  8  7  6  5  4  3  2  1  0 

NAND read: device 0 offset 0x1c0000, size 0x20000
 131072 bytes read: OK
MMC: no card present
starting USB...
USB0:   Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
USB1:   Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
USB2:   Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning bus 1 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Device 0: Vendor: SanDisk Rev: 1.00 Prod: Ultra
            Type: Removable Hard Disk
            Capacity: 14875.0 MB = 14.5 GB (30464000 x 512)
... is now current device
Scanning usb 0:1...
** Unable to read file / **
Found EFI removable media binary efi/boot/bootaa64.efi
Scanning disks on usb...
Disk usb1 not ready
Disk usb2 not ready
Disk usb3 not ready
Scanning disks on mmc...
MMC: no card present
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
1206008 bytes read in 61 ms (18.9 MiB/s)
## Starting EFI application at 81000000 ...
FM1@DTSEC3 Waiting for PHY auto negotiation to complete......... TIMEOUT !
FM1@DTSEC3: Could not initialize
error: serial port `com0' isn't found.
error: terminal `serial' isn't found.
error: terminal `serial' isn't found.
Use the ▲ and ▼ keys to change the selection.                   
      Press 'e' to edit the selected item, or 'c' for a command prompt.          Fedora 28 (Twenty Eight)                                                       Advanced options for Fedora 28 (Twenty Eight)                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                  The selected entry will be started automatically in 5s.                        The selected entry will be started automatically in 4s.                        The selected entry will be started automatically in 3s.                        The selected entry will be started automatically in 2s.                        The selected entry will be started automatically in 1s.                        The selected entry will be started automatically in 0s.                     EFI stub: Booting Linux Kernel...
EFI stub: Using DTB from configuration table
EFI stub: Exiting boot services and installing virtual address map...
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 4.16.0-10933-gedbdfd0 (matt@fedora-arm64) (gcc version 4.8.5 20150623 (Red Hat 4.8.5-16) (GCC)) #1 SMP PREEMPT Tue Apr 10 04:01:21 UTC 2018
[    0.000000] Machine model: Traverse LS1043S
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: EFI v2.70 by Das U-Boot
[    0.000000] efi:  SMBIOS=0xfaada000 
[    0.000000] Reserved memory: created DMA memory pool at 0x00000008ffc00000, size 4 MiB
[    0.000000] OF: reserved mem: initialized node qman-fqd, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x00000008fc000000, size 32 MiB
[    0.000000] OF: reserved mem: initialized node qman-pfdr, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x00000008fe000000, size 16 MiB
[    0.000000] OF: reserved mem: initialized node bman-fbpr, compatible id shared-dma-pool
[    0.000000] cma: Reserved 16 MiB at 0x00000000fac00000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000008ffbfffff]
[    0.000000] NUMA: NODE_DATA [mem 0x8ffbd0800-0x8ffbd22ff]
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x0000000080000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000008ffbfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x0000000087ffffff]
[    0.000000]   node   0: [mem 0x0000000088000000-0x0000000088007fff]
[    0.000000]   node   0: [mem 0x0000000088011000-0x00000000faad7fff]
[    0.000000]   node   0: [mem 0x00000000faad8000-0x00000000faae5fff]
[    0.000000]   node   0: [mem 0x00000000faae6000-0x00000000fbda6fff]
[    0.000000]   node   0: [mem 0x00000000fbda7000-0x00000000fbda8fff]
[    0.000000]   node   0: [mem 0x00000000fbda9000-0x00000000fbdfffff]
[    0.000000]   node   0: [mem 0x0000000880000000-0x00000008fbffffff]
[    0.000000]   node   0: [mem 0x00000008ff000000-0x00000008ffbfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000008ffbfffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.2 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] random: fast init done
[    0.000000] percpu: Embedded 24 pages/cpu @        (ptrval) s57624 r8192 d32488 u98304
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1002183
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinux-4.16.0-10933-gedbdfd0 root=PARTUUID=d36d7382-a921-40b6-94fe-1a4251b02771 ro console=ttyS0,115200 rootwait net.ifnames=0
[    0.000000] software IO TLB [mem 0xf69af000-0xfa9af000] (64MB) mapped at [        (ptrval)-        (ptrval)]
[    0.000000] Memory: 3910088K/4073436K available (8188K kernel code, 560K rwdata, 2908K rodata, 640K init, 367K bss, 146964K reserved, 16384K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Adjusting CPU interface base to 0x000000000142f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858
[    0.000000] arch_timer: CPU0: Trapping CNTVCT access
[    0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.000150] Console: colour dummy device 80x25
[    0.000184] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
[    0.000191] pid_max: default: 32768 minimum: 301
[    0.000235] Security Framework initialized
[    0.001350] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.001904] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.001936] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.001957] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.020004] ASID allocator initialised with 32768 entries
[    0.028002] Hierarchical SRCU implementation.
[    0.036177] Remapping and enabling EFI services.
[    0.044022] smp: Bringing up secondary CPUs ...
[    0.072101] Detected VIPT I-cache on CPU1
[    0.072126] arch_timer: CPU1: Trapping CNTVCT access
[    0.072130] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.100128] Detected VIPT I-cache on CPU2
[    0.100142] arch_timer: CPU2: Trapping CNTVCT access
[    0.100146] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.128174] Detected VIPT I-cache on CPU3
[    0.128187] arch_timer: CPU3: Trapping CNTVCT access
[    0.128191] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.128229] smp: Brought up 1 node, 4 CPUs
[    0.128245] SMP: Total of 4 processors activated.
[    0.128250] CPU features: detected: 32-bit EL0 Support
[    0.130416] CPU: All CPU(s) started at EL2
[    0.130425] alternatives: patching kernel code
[    0.130872] devtmpfs: initialized
[    0.133761] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.133796] futex hash table entries: 1024 (order: 5, 131072 bytes)
[    0.134381] SMBIOS 3.0 present.
[    0.134394] DMI: traverse ls1043s/ls1043s, BIOS 2018.03-00006-g3f3fcc06e9-dirty 03/23/2018
[    0.134545] NET: Registered protocol family 16
[    0.134743] audit: initializing netlink subsys (disabled)
[    0.134816] audit: type=2000 audit(0.132:1): state=initialized audit_enabled=0 res=1
[    0.135232] cpuidle: using governor menu
[    0.135314] vdso: 2 pages (1 code @ 0000000026f54479, 1 data @ 000000000fd84fb8)
[    0.135324] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.135876] DMA: preallocated 256 KiB pool for atomic allocations
[    0.135933] Serial: AMBA PL011 UART driver
[    0.136900] Machine: Traverse LS1043S
[    0.136904] SoC family: QorIQ LS1043A
[    0.136907] SoC ID: svr:0x87920011, Revision: 1.1
[    0.147117] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.147340] cryptd: max_cpu_qlen set to 1000
[    0.147772] ACPI: Interpreter disabled.
[    0.147958] vgaarb: loaded
[    0.148122] SCSI subsystem initialized
[    0.148378] usbcore: registered new interface driver usbfs
[    0.148406] usbcore: registered new interface driver hub
[    0.148449] usbcore: registered new device driver usb
[    0.148729] imx-i2c 2180000.i2c: can't get pinctrl, bus recovery not supported
[    0.160754] pca953x 0-0024: interrupt support not compiled in
[    0.161049] i2c i2c-0: IMX I2C adapter registered
[    0.161061] i2c i2c-0: can't use DMA, using PIO instead.
[    0.161144] imx-i2c 21b0000.i2c: can't get pinctrl, bus recovery not supported
[    0.161262] i2c i2c-1: IMX I2C adapter registered
[    0.161268] i2c i2c-1: can't use DMA, using PIO instead.
[    0.161348] pps_core: LinuxPPS API ver. 1 registered
[    0.161351] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.161366] PTP clock support registered
[    0.161390] EDAC MC: Ver: 3.0.0
[    0.161574] Registered efivars operations
[    0.161587] efivars: get_next_variable: status=8000000000000007
[    0.162018] clocksource: Switched to clocksource arch_sys_counter
[    0.162097] VFS: Disk quotas dquot_6.6.0
[    0.162127] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.162211] pnp: PnP ACPI: disabled
[    0.166321] NET: Registered protocol family 2
[    0.166668] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
[    0.166729] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.166969] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.167373] TCP: Hash tables configured (established 32768 bind 32768)
[    0.167449] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.167516] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.167634] NET: Registered protocol family 1
[    0.167843] RPC: Registered named UNIX socket transport module.
[    0.167847] RPC: Registered udp transport module.
[    0.167850] RPC: Registered tcp transport module.
[    0.167854] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.168340] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.168564] kvm [1]: 8-bit VMID
[    0.169006] kvm [1]: vgic interrupt IRQ1
[    0.169065] kvm [1]: Hyp mode initialized successfully
[    0.170742] Initialise system trusted keyrings
[    0.170801] workingset: timestamp_bits=44 max_order=20 bucket_order=0
[    0.174877] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.175258] NFS: Registering the id_resolver key type
[    0.175275] Key type id_resolver registered
[    0.175278] Key type id_legacy registered
[    0.175286] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.175382] 9p: Installing v9fs 9p2000 file system support
[    0.175437] pstore: using deflate compression
[    0.177033] Key type asymmetric registered
[    0.177038] Asymmetric key parser 'x509' registered
[    0.177130] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.177136] io scheduler noop registered
[    0.177250] io scheduler cfq registered (default)
[    0.177255] io scheduler mq-deadline registered
[    0.177258] io scheduler kyber registered
[    0.178378] PCI: OF: host bridge /soc/pcie@3500000 ranges:
[    0.178394] PCI: OF:    IO 0x4800010000..0x480001ffff -> 0x00000000
[    0.178402] PCI: OF:   MEM 0x4840000000..0x487fffffff -> 0x40000000
[    0.178499] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0000:00
[    0.178507] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.178512] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.178518] pci_bus 0000:00: root bus resource [mem 0x4840000000-0x487fffffff] (bus address [0x40000000-0x7fffffff])
[    0.191197] pci 0000:00:00.0: BAR 14: assigned [mem 0x4840000000-0x48402fffff]
[    0.191204] pci 0000:00:00.0: BAR 6: assigned [mem 0x4840300000-0x48403007ff pref]
[    0.191212] pci 0000:01:00.0: BAR 0: assigned [mem 0x4840000000-0x48401fffff 64bit]
[    0.191254] pci 0000:01:00.0: BAR 6: assigned [mem 0x4840200000-0x484020ffff pref]
[    0.191260] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    0.191266] pci 0000:00:00.0:   bridge window [mem 0x4840000000-0x48402fffff]
[    0.191404] pcieport 0000:00:00.0: Signaling PME with IRQ 66
[    0.191489] pcieport 0000:00:00.0: AER enabled with IRQ 66
[    0.191599] PCI: OF: host bridge /soc/pcie@3600000 ranges:
[    0.191612] PCI: OF:    IO 0x5000010000..0x500001ffff -> 0x00000000
[    0.191619] PCI: OF:   MEM 0x5040000000..0x507fffffff -> 0x40000000
[    0.191704] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0001:00
[    0.191710] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.191717] pci_bus 0001:00: root bus resource [io  0x10000-0x1ffff] (bus address [0x0000-0xffff])
[    0.191723] pci_bus 0001:00: root bus resource [mem 0x5040000000-0x507fffffff] (bus address [0x40000000-0x7fffffff])
[    0.194166] pci 0001:00:00.0: BAR 6: assigned [mem 0x5040000000-0x50400007ff pref]
[    0.194173] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    0.194289] pcieport 0001:00:00.0: Signaling PME with IRQ 67
[    0.194347] pcieport 0001:00:00.0: AER enabled with IRQ 67
[    0.195559] bman_ccsr 1890000.bman: assigned reserved memory node bman-fbpr
[    0.199188] qman_ccsr 1880000.qman: assigned reserved memory node qman-fqd
[    0.200431] qman_ccsr 1880000.qman: assigned reserved memory node qman-pfdr
[    0.201868] bman_portal 508000000.bman-portal: Portal initialised, cpu 0
[    0.201924] bman_portal 508010000.bman-portal: Portal initialised, cpu 1
[    0.201989] bman_portal 508020000.bman-portal: Portal initialised, cpu 2
[    0.202107] bman_portal 508030000.bman-portal: Portal initialised, cpu 3
[    0.202508] qman_portal 500000000.qman-portal: Portal initialised, cpu 0
[    0.202578] qman_portal 500010000.qman-portal: Portal initialised, cpu 1
[    0.202646] qman_portal 500020000.qman-portal: Portal initialised, cpu 2
[    0.203065] qman_portal 500030000.qman-portal: Portal initialised, cpu 3
[    0.204983] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.206137] console [ttyS0] disabled
[    0.206177] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 38, base_baud = 25000000) is a 16550A
[    1.371780] console [ttyS0] enabled
[    1.375599] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 38, base_baud = 25000000) is a 16550A
[    1.384663] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 39, base_baud = 25000000) is a 16550A
[    1.393724] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 39, base_baud = 25000000) is a 16550A
[    1.407125] loop: module loaded
[    1.412077] libphy: Fixed MDIO Bus: probed
[    1.416351] tun: Universal TUN/TAP device driver, 1.6
[    1.422919] libphy: Freescale XGMAC MDIO Bus: probed
[    1.429353] libphy: Freescale XGMAC MDIO Bus: probed
[    1.434896] libphy: Freescale XGMAC MDIO Bus: probed
[    1.440491] libphy: Freescale XGMAC MDIO Bus: probed
[    1.446071] libphy: Freescale XGMAC MDIO Bus: probed
[    1.451646] libphy: Freescale XGMAC MDIO Bus: probed
[    1.457216] libphy: Freescale XGMAC MDIO Bus: probed
[    1.462796] libphy: Freescale XGMAC MDIO Bus: probed
[    1.468364] libphy: Freescale XGMAC MDIO Bus: probed
[    1.488204] fsl_dpaa_mac 1ae0000.ethernet: FMan MEMAC
[    1.493259] fsl_dpaa_mac 1ae0000.ethernet: FMan MAC address: 00:0a:fa:24:23:79
[    1.500856] fsl_dpaa_mac 1ae2000.ethernet: FMan MEMAC
[    1.505908] fsl_dpaa_mac 1ae2000.ethernet: FMan MAC address: 00:0a:fa:24:23:7a
[    1.513391] fsl_dpaa_mac 1ae4000.ethernet: FMan MEMAC
[    1.518444] fsl_dpaa_mac 1ae4000.ethernet: FMan MAC address: 00:0a:fa:24:23:7d
[    1.525921] fsl_dpaa_mac 1ae6000.ethernet: FMan MEMAC
[    1.530973] fsl_dpaa_mac 1ae6000.ethernet: FMan MAC address: 00:0a:fa:24:23:7e
[    1.538563] fsl_dpaa_mac 1ae8000.ethernet: FMan MEMAC
[    1.543614] fsl_dpaa_mac 1ae8000.ethernet: FMan MAC address: 00:0a:fa:24:23:7b
[    1.551202] fsl_dpaa_mac 1aea000.ethernet: FMan MEMAC
[    1.556253] fsl_dpaa_mac 1aea000.ethernet: FMan MAC address: 00:0a:fa:24:23:7c
[    1.563726] fsl_dpaa_mac 1af0000.ethernet: FMan MEMAC
[    1.568779] fsl_dpaa_mac 1af0000.ethernet: FMan MAC address: 00:0a:fa:24:23:7f
[    1.585610] fsl_dpaa_mac 1ae0000.ethernet eth0: Probed interface eth0
[    1.601952] fsl_dpaa_mac 1ae2000.ethernet eth1: Probed interface eth1
[    1.618540] fsl_dpaa_mac 1ae4000.ethernet eth2: Probed interface eth2
[    1.634679] fsl_dpaa_mac 1ae6000.ethernet eth3: Probed interface eth3
[    1.650600] fsl_dpaa_mac 1ae8000.ethernet eth4: Probed interface eth4
[    1.665948] fsl_dpaa_mac 1aea000.ethernet eth5: Probed interface eth5
[    1.681866] fsl_dpaa_mac 1af0000.ethernet eth6: Probed interface eth6
[    1.688420] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.694257] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.700235] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    1.707194] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.712807] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    1.720633] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.726691] VFIO - User Level meta-driver version: 0.3
[    1.732505] ------------[ cut here ]------------
[    1.737121] dwc3 2f00000.usb3: request value same as default, ignoring
[    1.743681] WARNING: CPU: 1 PID: 1 at drivers/usb/dwc3/core.c:287 dwc3_core_init+0x984/0x99c
[    1.752105] Modules linked in:
[    1.755154] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.16.0-10933-gedbdfd0 #1
[    1.762364] Hardware name: traverse ls1043s/ls1043s, BIOS 2018.03-00006-g3f3fcc06e9-dirty 03/23/2018
[    1.771484] pstate: 60000005 (nZCv daif -PAN -UAO)
[    1.776265] pc : dwc3_core_init+0x984/0x99c
[    1.780437] lr : dwc3_core_init+0x984/0x99c
[    1.784609] sp : ffff00000803bbb0
[    1.787912] x29: ffff00000803bbb0 x28: 0000000000000000 
[    1.793215] x27: ffff000008c91000 x26: 0000000000000133 
[    1.798517] x25: ffff000008888000 x24: ffff80087508cbb8 
[    1.803818] x23: ffff800877a91c10 x22: ffff800877a70300 
[    1.809121] x21: 0000000000000041 x20: 0000000030c11004 
[    1.814423] x19: ffff800876374818 x18: ffff0000088f29a0 
[    1.819725] x17: 000000000000000e x16: 0000000000000001 
[    1.825027] x15: 0000000000000001 x14: ffffffffffffffff 
[    1.830329] x13: 0000000000000000 x12: 0101010101010101 
[    1.835631] x11: 0000000000000000 x10: 0000000000000129 
[    1.840933] x9 : 0000000000000007 x8 : 69726f6e6769202c 
[    1.846235] x7 : 746c756166656420 x6 : 0000000000000000 
[    1.851537] x5 : 0000000000000000 x4 : 0000000000000000 
[    1.856838] x3 : ffffffffffffffff x2 : ffff000008c20fc0 
[    1.862140] x1 : 0000000000000000 x0 : 000000000000003a 
[    1.867442] Call trace:
[    1.869879]  dwc3_core_init+0x984/0x99c
[    1.873704]  dwc3_probe+0x7cc/0xa70
[    1.877182]  platform_drv_probe+0x50/0xbc
[    1.881182]  driver_probe_device+0x254/0x2f0
[    1.885442]  __driver_attach+0xa4/0xa8
[    1.889181]  bus_for_each_dev+0x50/0xa0
[    1.893005]  driver_attach+0x20/0x28
[    1.896570]  bus_add_driver+0x1c0/0x224
[    1.900395]  driver_register+0x68/0x108
[    1.904219]  __platform_driver_register+0x48/0x50
[    1.908914]  dwc3_driver_init+0x18/0x20
[    1.912740]  do_one_initcall+0x38/0x124
[    1.916568]  kernel_init_freeable+0x188/0x230
[    1.920915]  kernel_init+0x10/0x100
[    1.924393]  ret_from_fork+0x10/0x18
[    1.927960] ---[ end trace 7a0d2e54f10f0025 ]---
[    1.934368] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.940895] ehci-pci: EHCI PCI platform driver
[    1.945360] ehci-platform: EHCI generic platform driver
[    1.951016] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    1.956510] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    1.964401] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x02010010
[    1.973128] xhci-hcd xhci-hcd.0.auto: irq 46, io mem 0x02f00000
[    1.979444] hub 1-0:1.0: USB hub found
[    1.983208] hub 1-0:1.0: 1 port detected
[    1.987290] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    1.992780] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    2.000437] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0  SuperSpeed
[    2.007074] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.015412] hub 2-0:1.0: USB hub found
[    2.019174] hub 2-0:1.0: 1 port detected
[    2.023287] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    2.028779] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    2.036669] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x02010010
[    2.045388] xhci-hcd xhci-hcd.1.auto: irq 47, io mem 0x03000000
[    2.051609] hub 3-0:1.0: USB hub found
[    2.055370] hub 3-0:1.0: 1 port detected
[    2.059428] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    2.064918] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    2.072573] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0  SuperSpeed
[    2.079213] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.087540] hub 4-0:1.0: USB hub found
[    2.091306] hub 4-0:1.0: 1 port detected
[    2.095412] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[    2.100904] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 5
[    2.108790] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x02010010
[    2.117506] xhci-hcd xhci-hcd.2.auto: irq 48, io mem 0x03100000
[    2.123743] hub 5-0:1.0: USB hub found
[    2.127508] hub 5-0:1.0: 1 port detected
[    2.131574] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[    2.137063] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 6
[    2.144719] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0  SuperSpeed
[    2.151355] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.159679] hub 6-0:1.0: USB hub found
[    2.163444] hub 6-0:1.0: 1 port detected
[    2.167572] usbcore: registered new interface driver uas
[    2.172961] usbcore: registered new interface driver usb-storage
[    2.189976] rtc-isl1208 0-006f: rtc core: registered rtc-isl1208 as rtc0
[    2.197327] i2c /dev entries driver
[    2.202111] sdhci: Secure Digital Host Controller Interface driver
[    2.208287] sdhci: Copyright(c) Pierre Ossman
[    2.212714] Synopsys Designware Multimedia Card Interface Driver
[    2.219105] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.250594] mmc0: SDHCI controller on 1560000.esdhc [1560000.esdhc] using ADMA 64-bit
[    2.258948] ledtrig-cpu: registered to indicate activity on CPUs
[    2.265577] usbcore: registered new interface driver usbhid
[    2.271153] usbhid: USB HID core driver
[    2.275145] optee: probing for conduit method from DT.
[    2.280284] optee: api uid mismatch
[    2.283889] NET: Registered protocol family 17
[    2.288381] 9pnet: Installing 9P2000 support
[    2.292683] Key type dns_resolver registered
[    2.297340] registered taskstats version 1
[    2.301432] Loading compiled-in X.509 certificates
[    2.306259] Key type big_key registered
[    2.312575] rtc-isl1208 0-006f: setting system clock to 2018-04-12 08:01:00 UTC (1523520060)
[    2.326449] Waiting for root device PARTUUID=d36d7382-a921-40b6-94fe-1a4251b02771...
[    2.362094] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[    2.387350] usb-storage 2-1:1.0: USB Mass Storage device detected
[    2.393897] scsi host0: usb-storage 2-1:1.0
[    2.430064] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[    2.457697] hid-generic 0003:0451:926B.0001: device has no listeners, quitting
[    3.426448] scsi 0:0:0:0: Direct-Access     SanDisk  Ultra            1.00 PQ: 0 ANSI: 6
[    3.435021] sd 0:0:0:0: [sda] 30464000 512-byte logical blocks: (15.6 GB/14.5 GiB)
[    3.443455] sd 0:0:0:0: [sda] Write Protect is off
[    3.448502] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    3.469507]  sda: sda1 sda2 sda3 sda4
[    3.474677] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    3.493174] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[    3.500848] VFS: Mounted root (ext4 filesystem) readonly on device 8:4.
[    3.508385] devtmpfs: mounted
[    3.511538] Freeing unused kernel memory: 640K
[    3.937380] NET: Registered protocol family 10
[    3.942578] Segment Routing with IPv6
[    3.972410] efivars: get_next_variable: status=8000000000000007
[    3.984540] systemd[1]: systemd 238 running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    4.006135] systemd[1]: Detected architecture arm64.

Welcome to Fedora 28 (Twenty Eight)!

[    4.034782] systemd[1]: Set hostname to <fedora-arm64>.
[    4.307901] systemd[1]: File /usr/lib/systemd/system/systemd-journald.service:35 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[    4.325295] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[    4.470842] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    4.490291] systemd[1]: Listening on Journal Audit Socket.
[  OK  ] Listening on Journal Audit Socket.
[    4.514376] systemd[1]: Listening on Process Core Dump Socket.
[  OK  ] Listening on Process Core Dump Socket.
[    4.534205] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
[    4.558954] systemd[1]: Created slice User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[  OK  ] Reached target Slices.
[  OK  ] Listening on Journal Socket (/dev/log).
[  OK  ] Created slice system-getty.slice.
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[  OK  ] Created slice system-systemd\x2dfsck.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-sshd\x2dkeygen.slice.
[  OK  ] Listening on udev Kernel Socket.
[  OK  ] Listening on Journal Socket.
         Starting Setup Virtual Console...
         Starting Journal Service...
         Mounting Kernel Debug File System...
         Starting Apply Kernel Variables...
         Mounting Kernel Configuration File System...
         Mounting POSIX Message Queue File System...
         Mounting Huge Pages File System...
         Starting File System Check on Root Device...
[  OK  ] Listening on udev Control Socket.
         Starting udev Coldplug all Devices...
         Startin[    4.869044] audit: type=1130 audit(1523520063.052:2): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journald comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
g Create list of[    4.889148] audit: type=1130 audit(1523520063.072:3): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-vconsole-setup comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
 required st…c[    4.909330] audit: type=1131 audit(1523520063.072:4): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-vconsole-setup comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
e nodes for the current kernel..[    4.931759] audit: type=1130 audit(1523520063.116:5): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-sysctl comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
.
[  OK  ] Started J[    4.953684] audit: type=1130 audit(1523520063.136:6): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=kmod-static-nodes comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
ournal Service.
[  OK  ] Started Setup Virtual Console.
[  OK  ] Mounted Kernel Debug File System.
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Mounted Kernel Configuration File System.
[  OK  ] Mounted POSIX Message Queue File System.
[  OK  ] Mounted Huge Pages File System.
[  OK  ] Started Create list of required sta…vice nodes for the current kernel.
[  OK  ] Started File System Check on Root Device.
[    5.042215] audit: type=1130 audit(1523520063.228:7): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-fsck-root comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
         Starting Remount Root and Kernel File Systems...
[  OK  ] Started udev Coldplug all Devices.
[    5.098233] audit: type=1130 audit(1523520063.284:8): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udev-trigger comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    5.168636] EXT4-fs (sda4): re-mounted. Opts: (null)
[  OK  ] Started Remount Root and Kernel File Systems.
[    5.194152] audit: type=1130 audit(1523520063.380:9): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-remount-fs comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
         Starting Create Static Device Nodes in /dev...
         Starting Flush Journal to Persistent Storage...
         Starting Configure read-only root support...
[    5.274274] systemd-journald[3548]: Received request to flush runtime journal from PID 1
[  OK  ] Started Create Static Device Nodes in /dev.
[    5.298251] audit: type=1130 audit(1523520063.484:10): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-setup-dev comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
         Starting udev Kernel Device Manager...
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] Started Configure read-only root support.
[    5.550284] audit: type=1130 audit(1523520063.736:11): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=fedora-readonly comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
         Starting Load/Save Random Seed...
[  OK  ] Started Flush Journal to Persistent Storage.
[    5.598173] audit: type=1130 audit(1523520063.784:12): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journal-flush comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  OK  ] Started udev Kernel Device Manager.
[    5.634241] audit: type=1130 audit(1523520063.820:13): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udevd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  OK  ] Started Load/Save Random Seed.
[    5.666215] audit: type=1130 audit(1523520063.852:14): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-random-seed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
         Starting Show Plymouth Boot Screen...
[  OK      5.812238] audit: type=1130 audit(1523520063.996:15): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=plymouth-start comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
0m] Found device /dev/ttyS0.
[  OK  ] Started Show Plymouth Boot Screen.
[  OK  ] Reached target Local Encrypted Volumes.
[  OK  ] Reached target Paths.
[  OK  ] Started Forward Password Requests to Plymouth Directory Watch.
[  OK  ] Found device Ultra swap.
         Activating swap Swap Partition...
[  OK  ] Found device Ultra boot.
[  OK  ] Found device Ultra efi.
         Starting File System Check on /dev/…0[    5.996373] Adding 2097148k swap on /dev/sda3.  Priority:-2 extents:1 across:2097148k 
ff-f85c-4165-afa4-3ecb94ba50d0...
[  OK  ] Activated swap Swap Partition.
[  OK  ] Reached target Swap.
         Mounting Temporary Directory (/tmp)...
[  OK  ] Mounted Temporary Directory (/tmp).
[  OK      6.059944] audit: type=1130 audit(1523520064.244:16): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-fsck@dev-disk-by\x2dpartuuid-4507e0ff\x2df85c\x2d4165\x2dafa4\x2d3ecb94ba50d0 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
0m] Started File System Check on[    6.088726] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
 /dev/d…7e0ff-f85c-4165-afa4-3ecb94ba50d0.
         Mounting /boot...
[  OK  ] Mounted /boot.
         Mounting /boot/efi...
[  OK  ] Mounted /boot/efi.
[  OK  ] Reached target Local File Systems.
         Starting Create Volatile Files and Di[    6.127217] audit: type=1130 audit(1523520064.312:17): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=dracut-shutdown comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
rectories...
         Starting Restore /run/initramfs on shutdown...
         Starting Tell Plymouth To Write Out Runtime Data...
[  OK  ] Star[    6.159937] audit: type=1130 audit(1523520064.344:18): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-setup comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
ted Restore /run/initramfs on shutdown.
[  OK  ] Started Create Volatile Files and Directories.
[  OK  ] Started Tell Plymouth To Write Out Runtime Data.
         Starting Security Auditing Service...
[  OK  ] Started Security Auditing Service.
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Reached target System Initialization.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Listening on SSSD Secrets Service responder socket.
[  OK  ] Reached target Sockets.
[  OK  ] Started dnf makecache timer.
[  OK  ] Reached target Timers.
[  OK  ] Reached target Basic System.
[  OK  ] Reached target sshd-keygen.target.
         Starting System Security Services Daemon...
[  OK  ] Started D-Bus System Message Bus.
         Starting firewalld - dynamic firewall daemon...
[    6.908396] random: crng init done
[  OK  ] Started System Security Services Daemon.
[  OK  ] Reached target User and Group Name Lookups.
         Starting Login Service...
[  OK  ] Started Login Service.
[  OK  ] Started firewalld - dynamic firewall daemon.
[  OK  ] Reached target Network (Pre).
         Starting Network Manager...
         Starting Hostname Service...
[  OK  ] Started Hostname Service.
[  OK  ] Started Network Manager.
[  OK  ] Reached target Network.
         Starting OpenSSH server daemon...
         Starting Permit User Sessions...
         Starting Network Manager Script Dispatcher Service...
[  OK  ] Started Network Manager Script Dispatcher Service.
[  OK  ] Started Permit User Sessions.
         Starting Terminate Plymouth Boot Screen...
         Starting Hold until boot process finishes up...
[    9.269910] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    9.353089] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    9.370322] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[    9.449023] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[    9.466617] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[    9.476635] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[    9.494153] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[    9.504476] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[    9.521832] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready
[    9.601020] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready
[    9.618201] IPv6: ADDRCONF(NETDEV_UP): eth5: link is not ready
[    9.697003] IPv6: ADDRCONF(NETDEV_UP): eth5: link is not ready
[    9.714390] IPv6: ADDRCONF(NETDEV_UP): eth6: link is not ready
[    9.724276] IPv6: ADDRCONF(NETDEV_UP): eth6: link is not ready

Fedora 28 (Twenty Eight)
Kernel 4.16.0-10933-gedbdfd0 on an aarch64 (ttyS0)

fedora-arm64 login: [   10.498178] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[   10.530188] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[   10.722211] IPv6: ADDRCONF(NETDEV_CHANGE): eth6: link becomes ready